Before decorating, you must prepare a few things in your bag. Tape measure (buy 5m, not 3m), calculator, big plate clips (folder list, receipts); In addition, it is best to prepare old towels on the site early (the kind of soft cotton, rubbed with bricks) , plastic bag (wrapped on the pipe interface, can prevent dirt blockage)
(b) Choosing good days and launching artillery
Before the workers enter the court, it is best to measure the corners of the house in person, take them down, mark them clearly, and be sure not to be lazy. The contents of the measurement mainly include:
1. Identify the area involved in the renovation process. Especially the tiling area, wall paint area, wallpaper area, floor area;
2, clear the main wall size. In particular, it is necessary to design the wall size of the furniture later.
☆☆☆☆ At this time, you should go to buy a radiator ☆☆☆☆
(III) Demolition of the main body to make space more practical
The demolition of the main body is the first one to be put on the project. It mainly includes the demolition of walls, walls, shovels, removal of heat, replacement of steel windows, and so on. After the demolition of the completed garbage, it must be cleared up in time to ensure the cleanliness of the interior, but also to facilitate the construction.
☆☆☆☆ At this time, it is time to set the finished product door ☆☆☆☆
☆☆☆☆ It's best to put cabinets, hoods, stoves, and water heaters through them and decide on them. ☆☆☆☆
(IV) Hydropower Renovation, Arranging the Use of Each Space
Hydroelectric reform, no regrets medicine. Bricks on the wall, a ceiling, and then think of adding sockets can be difficult. Therefore, be sure to determine the exact location of switches, lamps, basins, bathtubs, washing machines, etc.
Before the hydropower reform, the cabinet designer should come to the door to make the first measurement and help you determine the power and waterway reconstruction plan.
Water heaters, it is also best to send someone to design the location of the power supply and the interface according to the model you have determined.
Remind you: On the wall under the basin, it is best to leave the power outlet for the kitchen.
The air-conditioning hole and power source should be placed on the wall of the bedside as much as possible to avoid air-conditioning blowing directly to people.
Strong electricity and weak points must maintain a 20-centimeter gap. For example, a distance of 20 cm must be left between the outlet and the cable.
(5) Pack up the tubes and wrap up the unsightly pipes
Considering the hygrogenic and hygroscopic environment of the kitchen and bathroom, the material of the standpipe must not be a wooden keel! Everyone must be careful that even the wood keel is not painted with anti-corrosion paint.
Remember to use a light steel keel, or a red brick, on the standpipe. Light steel keel provinces, but the most solid and easy to use is the red brick.
☆☆☆☆ It is necessary to buy tiles, caulking agents, etc.☆☆☆☆
☆☆☆☆Furniture should be set early and leave a good duration, usually at least 15 days or so☆☆☆☆
(six) tiling, the first thing with a solid texture
Before tiling, buy a floor drain.
Note: Floor drains are going to be bought in Oriental Homes. To buy a dedicated washing machine or shower floor drain, but also to deodorant function.
After finishing waterproofing and pulling hair, prepare a tiling.
In addition to the normal tiling, the tiles are soaked in water and dried in the shade; the tattered tiles are left for cutting, and I personally emphasize the overall beauty of the tiling. Simply put, it is the brick on the wall. The width cannot be less than 10 cm. Tiles often encounter this situation, for example, 1 meter wide wall, bricks 32 * 32cm, normal method, 3 whole 1 small. However, 32 × 3 = 96, but also to set aside 1 cm of joint space, and finally the small brick can only be posted 3cm wide. It's not my picky, narrow bricks posted there, it's hard to see how ugly it is.
As long as you make it clear to the tile master in advance, the width of the brick on the wall should not be less than 10 cm. He will cut tiles on both sides. Or just give an example of a wall that is just 1 meter wide, it becomes 2 whole 2 small. 32 × 2 = 64, set aside 1 cm of the joints, the small bricks on each side of 17.5cm on it. In this way, it seems that both sides are not only symmetrical, but neither the narrow wall nor the narrow wall will be obtrusive.
However, this practice costs money, please buy a good amount of money before buying bricks.
☆☆☆☆ At this time, basins and faucets should be determined, and the cabinet designer is invited to visit the house for the second time.☆☆☆☆
☆☆ At the same time buy paint (mixed or clear), wall paint, lacquer, diluted water, etc.
(seven) oil workers go into battle, scrub scrub brush
If you do not buy finished products, let the worker master do it.
Note: Any woodwork, even if it is just a mouthwash, must follow this step. The big board sinks and the veneer is veneered before painting. When mixing oil, there is an irresponsible worker who is lazy to brush oil directly on the big core board. This is absolutely wrong. Don’t believe the nonsense of selling Daxin boards individually. There is no problem with brushing oil directly. Remember, if you brush oil directly, it will take a long time for you to crack and remember.
Now do oil mixing, no brush, but spray. It is best to let workers spray white on the inside of the door and the meter box.
There is nothing to say about brushing the walls. Leveling, sanding, and brushing are all effective, and they absolutely depend on the craft of your oil worker.
My home is white paint except for the wallpaper, not the color of the brush. We need to remind everyone that if the walls are to be painted, the color must be noticed. The color of the recall must be lighter than that of the color card. It must not be the same as the color card or deeper than it is. Otherwise, you will regret it. Because at least two coats of paint are used to paint the walls, some of them are still three times. The color of the wall will be deeper than the one layer.
The method of painting is spraying or roller coating. The benevolent sees the person and the wise sees the wisdom. My home is roller-coating and I have not tried spraying it. It is said that the effect of spraying is better, but once it is destroyed, it will become difficult to repair the paint.
(8) wallpapers, beautiful walls
The wallpaper is better than the wall paint, and the effect is much better.
After the wall paint is brushed, the oil trader will apply nitro-lacquer to the place where the wallpaper is to be applied. The paint can dry after the next day, and then the master can paste the wallpaper. I just started worrying that the wallpaper will dirty the painted white wall, but I knew it later when I posted it. The wallpaper was really a very clean job! My worry is completely unnecessary.
Note: Do not open the window for ventilation within 48 hours after the wallpaper has been posted. Let it dry slowly.
Say good to the master, if there is an odd place in individual places, trouble him to repair it.
☆☆☆☆ At this time, buy the panel, socket, and lamp.☆☆☆☆
(9) Install socket panel
The socket panel can be installed in about half a day.
remind you:
1, the best outlet to buy with a switch function, especially the kitchen, so that rice cookers, microwave ovens can be removed from the power supply, with the switch to control.
2, although there is a good switch socket, but pay attention to practicality. According to my observation, the five-hole power supply with switch, three sockets are flat mouth, once your electrical appliances need a round mouth three items, there will be a depressed situation with empty plug socket board. Therefore, multiple sockets must also be used, even if it does not switch control!
☆☆☆☆ In this case, ceilings for kitchens and bathrooms should be purchased. ☆☆☆☆
☆☆☆☆ At this time, if you need to install Yuba, please purchase and install it before the ceiling ☆☆☆☆
(ten) kitchen ceiling, seal the last ugly part
First install the water heater and Yuba, after installation, the ceiling edge can be better half-package water heater, which is more beautiful convergence.
Note: 1, it is best to buy aluminum buckle ceiling, even if not removed after many years, selling scrap aluminum are worth a lot of money. On the other hand, pvc buckles look good, but the quality and performance are generally the same, and plastic things are worth a few dollars even if they sell waste.
2, buy buckle board, to ask the price of all-inclusive, do not buckle board, corner to buy. But the installation fee is another calculation.
(11) Installation of cabinets, the birth of a beautiful kitchen
Cabinets are a cooperating project and should be ordered in advance about hoods, stoves and sinks. It is best to send it on the same day and install it together with the cabinet.
We told the cabinet factory in advance that we would bring the artificial stone countertops with the cut off of the stoves and the sinks in place, and n more money would not be given to the manufacturers. It is useful to include a water meter, a pipe, or something.
(12) Installation of finished products
Finished doors should be installed before the floor, mainly because of the complex installation steps, hinges, door locks, door stoppers, door frames, etc., using a large number of tools, such as the first installed floor, bumps are difficult to avoid. My family first installed the floor and then installed the door. There were many small pits on the floor. The meat hurt me.
(13) Installation of drying racks, curtain rods, lamps, sanitary ware, and bathroom hardware
It is recommended that before the installation of the floor, the items with a large amount of scattered ash will be handled one by one.
(14) Installing the floor
Before the floor is installed, we must do a leveling job. I have a lot of neighbors' floors that are not used for leveling, so both I and Lao Mao care about it. Unexpectedly, after the floor was laid, the aisle was gone and it was very depressing. Had to remove it and re-pour it after leveling it with dusting powder.
Prepare a little pepper in advance, do not buy the so-called insecticide powder brought by floor workers, let them sprinkle along the kick corner on the line.
Workers must be required not to cut the floor in the house, cut in the corridor, and finally clean the corridor.
(15) Installing a heat sink
At the end of the renovation, it is the easiest to ignore.
It must be clearly stated in advance with js. If the chapter on the installation sheet is not a manufacturer's stamp, it will not be accepted.
Pay attention to the installation of the radiator, (not a purchase order), who is the part of the seal? Many js is so operated, the purchase of a single cover is the manufacturer's chapter; installation of a single cover is the chapter of the installation team. In this way, the so-called "protection × × years" is only the guarantee of the radiator itself, but the material is not steel or copper and aluminum, as long as the factory can be almost no quality problems. The easiest place to go wrong is to install! If you agree with the chapter of the installation team, it basically means that you gave up the right to let the manufacturer responsible. Once there is an accident that has soaked the floor and flooded the home, manufacturers will absolutely shirk their responsibilities and it will be impossible for the installation team to find anyone. The so-called warranty can only be borne by the user.
(16) Land reclamation and cleaning
The biggest manifestation of cleaning, I think is to clean glass. It is a terrifying thing for a tall building to climb outside and rub it. Followed by the floor waxing, wax to buy their own, cheap and easy to use, but must use a cleaning waxing machine, efficiency is tens of times faster than artificial, hundreds of times.
In other respects, I don't think I need to rely too much on cleaning. They also use small blades to scrape here and scrape there, not so much.
Therefore, after the cleaning goes, it's best to do a thorough cleaning again. Go to the supermarket to buy a bag of "five clean powder" and get a few old towels. Use an old towel, stained with dried Wu Jie powder, from the mouth to the door, from the tiles to the kick corner, a house, a house of rub, do not be lazy, the result will definitely make you proud.
(17) Entry of furniture and home appliances
In a new home, furniture bears the brunt. Beds, mattresses, wardrobes, shoe cabinets, sofas, dining tables, etc.
Remind you: before the furniture enters the market, you should prepare the following items: disposable shoe covers (do not buy poor quality, step on the break), a few boxes of activated carbon, ladders, floor protection film (carrying closet, TV cabinet, etc. The floor is a protection).
If you buy a fabric bed, remind you to see if the fabric can be taken down. Because I could not tolerate the static electricity of the chemical fiber, I wanted to remove the original fabric cover the next day. When I made a set of pure cotton, I found that the fabric cover was too long and was nailed into the bed box. The workers are lazy and think that I won't split the covers a year or a half. I do not know whether someone else has such experience, anyway, the master worker ran a trip the next day, and the death of the bed was quite troublesome. Home appliances quickly delivery, tight or not in a hurry to wait and so on. Anyway, electrical appliances are getting more advanced and cheaper.
(18) Accessories have a taste
With a decorative ornament and beautiful curtains, the soft taste of the home came out.
Remind you: curtains do not spend too much money on dressings, curtains, plumb bobs are the money to be added, but lace, cloth buckles, tassels, these eight yuan, that ten yuan, have to spend more than two meters Thirty yuan is not necessary, and it is not necessarily beautiful.
Nature Flooring del floor Painted Sockets Wallpapers Switching windows Kitchen furniture Kitchens Fabrics Sofa cushions Floor tiles Fabric sofas White furniture Glass tables Glass dining tables Kitchen glass Sliding doors Functional sofas Sofas Sofas Dining tables and chairs Glass doors Function sofas Glass bricks Cabinets TVs Wallpapers Fabric Bed Glass Furniture Home Table Kitchen & Bathroom Ceiling Red Brick Cloth Curtains Kitchen Cabinet Doors Kitchen Bathroom Ceilings Bathroom Tiles Bathroom Doors Bathroom Tiles Color Bathroom Door Size Bathroom Size Bathroom Ceiling Material Bathroom Waterproof Price Toilet Ceiling Overall Bathroom Toilet Design Toilet Waterproof Floor Tile Tiles Price Kitchen tiles
Previous How to create a perfect home supervision teach you to identify the details of decoration
Next Interior decoration matters needing attention 172 house decoration matters needing attention
1. When the tools are in place and ready for renovation, several things must be prepared and placed in your bag. Tape measure (5m), calculator, large plate clips (folder list, receipts). In addition, it is best to prepare old towels (soft cotton, rubbed bricks), plastic bags (wrapped in On the pipeline interface, it can block the blockage of the dirt.2.Choose a good day and let the gun start. Before the worker enters the court, it is best to measure the corner of the house in person and take a pencil rule....
(A) tools in place, ready to be renovated before the decoration, you must prepare a few things in your bag. Tape measure (buy 5m, not 3m), calculator, big plate clips (folder list, receipts); In addition, it is best to prepare old towels on the site early (the kind of soft cotton, rubbed with bricks) , plastic bags (wrapped on the pipe interface, can prevent dirt block) (b) choose good days auspicious, put the gun to start before workers enter the field, it is best to the home corner
First, the tool is in place, ready for decoration Before the decoration, you must prepare a few things in your bag. Tape measure (buy 5m, not 3m), calculator, big plate clips (folder list, receipts); In addition, it is best to prepare old towels on the site early (the kind of soft cotton, rubbed with bricks) , plastic bag (wrapped on the pipe interface, can prevent dirt blockage). Second, arrange it properly and prepare to start work Before the workers enter the market, it is best to personally drop the corner of the house.
First, the tools are in place. Before you are ready to decorate, you must prepare a few things in your bag. Tape measure (buy 5m, not 3m), calculator, big plate clips (folder list, receipts); In addition, it is best to prepare old towels on the site early (the kind of soft cotton, rubbed with bricks) , plastic bag (wrapped on the pipe interface, can prevent dirt blockage). Second, arrange it properly, prepare to start work Before the workers enter the market, it is best to personally measure the corner of the home
First, the tool is in place, ready for decoration Before the decoration, you must prepare a few things in your bag. Tape measure (buy 5m, not 3m), calculator, big plate clips (folder list, receipts); In addition, it is best to prepare old towels on the site early (the kind of soft cotton, rubbed with bricks) , plastic bag (wrapped on the pipe interface, can prevent dirt blockage). Second, arrange it properly and prepare to start construction before workers enter the market
submit
Tungsten Carbide Tools,Tungsten Carbide Rings ,Carbide Rings ,Tungsten Carbide Inserts
Machine Tools Accessories Co., Ltd. , http://www.nbtungstencarbide.com