High shear emulsion pump is the use of high-speed rotating shear wheel and static shear wheel with the liquid material and the mixture for full high-speed shear, the milk are homogeneous, dispersed, mixing and so on. This equipment is to learn from foreign advanced technology and technology development and production of new products, the finger that reached the advanced domestic level, and now to introduce the use of TRL1 high shear emulsion pump attention and maintenance methods. TRL1 high shear emulsification pump The use of TRL1 high shear emulsification pump Attention and maintenance 1, TRL1 pipeline type pipeline equipment is usually connected before the mechanical seal cooling water, shut down when shut down and then cut off the cooling water. Cooling water can be tap water. Cooling water pressure ≦ 0.2Mpa. The material must enter the working chamber before it can be switched on, and it should be ensured that the mechanical seal (mechanical seal) is burned out due to high temperature or the service life is not caused by running without breaking. Cooling water inlet and outlet fittings equipped with hose size diameter? 5mm skin tube. 2, Make sure to turn on the machine seal cooling water, start the motor, and repeatedly asked the motor steering should be consistent with the spindle steering signs can work, non-reversal! 3, the use of machinery, liquid materials must be continuously input or in the container Keep a certain amount. Should avoid the empty machine running, so as to avoid the material in the work of high temperature or crystal solidification and equipment damage, non-slip! 4, usually only through the high weight TRL1 pipeline equipment into the material, the feed must be continuous input, keep the material Have better liquidity. When the material flow is poor, the viscosity of ≧ 4000CP SRH pipeline equipment imported pump, pump into the pressure 0.3Mpa. Select the pump should be colloid pump (cam rotor pump) and the like, the flow and the selected pipeline emulsion machine to match the flow range. (Should be greater than the minimum flow value, less than the maximum flow value) 5, metal shavings or hard and unbreakable debris into the working chamber is strictly prohibited to avoid destructive damage to the working stator, rotor and equipment. 6, the device in the course of the operation once an abnormal sound or other failure, should immediately stop checking until the fault is removed and then run. After the shutdown should be within the working chamber and set, the rotor clean. 7, TRL1 pipeline pipeline equipment such as process chamber can be replenished insulation layer, used to cool or heat the material, turn on the coolant or heat transfer oil. Insulation sandwich working pressure ≤ 0.2Mpa, in the processing of temperature requirements (such as asphalt) must be heated or cooled to normal operating temperature, crank, boot. 8, equipment in flammable, explosive working environment, you must use the appropriate level of explosion-proof motor. 9, after the production is finished, the equipment must be clean and clean so as to keep the working efficiency of the rotor and the sealing of the machine. If necessary, design and install a cleaning cycle device near the periphery. 10, according to different media users, the import and export filters must be regularly cleaned in order to avoid the reduction of feed and affect the production efficiency. Material into the work chamber must be fluid, do not allow dry powder, clumps of material directly into the machine, otherwise it will cause boring and damage to the equipment. 11, Regularly check the stator and rotor, found excessive wear and tear, should be promptly replaced the appropriate components to ensure dispersion, emulsifying effect. 12, TRL1 pipeline pipeline equipment found in the operation shaft leakage of liquid at the shaft, you must adjust the machine seal pressure after shutdown. (In the back attached: Mechanical seal instructions for use when detailed) 13, Before using this equipment to develop a corresponding safety in production practices, to ensure that operators and equipment safety. In the electrical control system users want to set the safety protection system, and there is a good and reliable electric motor grounding device. Further Reading: pump valve pipe fittings Exhibition Water Expo Xiamen exhibition of marine equipment Internet + Forum Yiwu Fair 2016 exhibition mold top ten brands of the Internet information industry (Xiamen) Technology Co., Ltd. Author: Asian pumps Network Editor: Yao Xiaoxia (QQ / WeChat: 2355962924) http://beng.liuti.cn/ (Service Hotline: 400-6030-811)
