For most users, Yuba has become the most commonly used equipment in the bathroom, and it is also one of the indispensable facilities in life. Therefore, choosing a suitable Yuba product can not only bring a comfortable life, but also play a certain role. The decorative effect, from the current installation of Yuba, it mainly depends on the manual operation, subject to a variety of factors, so the correct way of installation is critical, then the installation steps of Yuba what? Let's take a look.
Yuba installation steps: determine the location of the bathroom heater
Generally speaking, in order to obtain the best heating effect, these products should be located directly above the center of the bathtub or shower room, and the height should be controlled between 2.1 ~ 2.3m, and the ceiling is recommended to use materials with better strength and not easy to resonate , too high or too low will affect the use of results.
Yuba installation steps: install ventilation window
Since the bathroom is a place where the water vapour is relatively heavy, and the heat generated by the water heater is also very large, it is recommended to set a ventilation window in this area, put one end of the ventilation pipe on the ventilation window, and the other end is fixed to the exterior wall along the ventilation window along the wall. At the air outlet, the gap between the ventilation pipe and the ventilation hole is filled with cement.
Yuba installation steps: open vent ventilation fan
If there are ceilings in the home, then this step can be ignored. Users without ceilings should refer to the requirements and methods for setting up the installation ports according to different buckles in order to list the outlet size standards. Generally, Aluminum buckle plate ceiling bath size 300*300mm, while the ceiling should be reserved before the installation size of Yuba.
Yuba installation steps: fixed Yuba
After the above procedures are completed, the next step is to fix the product. First remove the panel cover, then spin down all the bulbs, connect each line with the switch panel, and open the terminal cover on the cabinet, press the wiring As shown in the figure and the terminal mark, connect the wire cover, and fix the terminal cover with screws.
Yuba installation precautions
1, because it is electricity products, so the wiring between the wires must be standardized, otherwise prone to short-circuit or explosion and other conditions, in general, the power of the Yuba up to 1100W, so the power wiring must be a waterproof line during installation It is best not to use multi-filament copper wires below 1 mm. In addition, all power wiring must be made of plastic tubes embedded in the wall. No open-wire setting is allowed.
2, in the purchase, do not choose too thick Yuba, usually about 20 cm can be, because it is placed on the roof, so you must add a layer of roof in the area below the roof, that is, PVC ceiling, so In order to make the second half of the Yuba can be sandwiched between the two top, if the Yuba is too thick, it will lead to difficult decoration.
Summary: Well, the above is about the content of the installation of the bathroom tyrants which are introduced, I hope to provide you with some help, I believe that in the future installation process of Yuba, friends will be more handy, to create their own satisfactory results.
Our Graphite Electrode was made of high-quality Petroleum Coke, needle coke, coal tar pitch and other low-ash raw materials. Processing by calcining, ingredients, mixed kneading, molding, roasting and pressure impregnation at 3000 ℃ high temperature graphite. We offers the most demanded standard graphite electrodes and nipples. Our graphite electrodes include RP, HP and UHP grades. They are widely used in electric arc furnaces (EAF) and ladle furnaces (LF) for the melting of steel, non-ferrous metals and some non-metallic minerals.
Advantage
1. High quality and strictly inspected petroleum coke, needle coke as raw material.
2. Low specific resisvitiy
3. Low conspumption rate
4. Anti-oxidation, uniform strength
5. Good resistance to thermal shock
6. Perfect match betwee body and nipple.
7. Professional , experienced reliable and safe package & transportation
Rp 200 Graphite Electrode,Small Size Graphite Electrode,Artificial Graphite Electrodes,Graphite Electrodes Regular Power
Carbographite Industrial PTE.LTD , https://www.carbographite.com